How to Perform a Slit Lamp Examination Step by Step

A slit lamp examination uses a thin, adjustable beam of light and a binocular microscope to inspect the front of the eye. Run it in order: prepare the room and patient, set the eyepieces, scan with diffuse light, narrow the beam, add filters, then record findings and clean the unit.

Before the Patient Sits Down

A clean slit lamp examination is half decided before anyone looks through the eyepieces.

Room and lighting

Dim the room. A semi-dark space lets the examiner's eyes adapt, so faint changes show up even under low light. StatPearls (NCBI).[1]

Patient position

  • Adjustable-height chair

  • Chin on the rest, forehead against the band

  • Eye level with the canthus mark

  • Fixation target at eye level

Instrument hygiene

Wipe the chin rest, forehead band and handles with a lint-free cloth dampened with alcohol, and replace the chin-rest paper after every patient. It takes ten seconds. Skip it and a quiet clinic earns a bad reputation fast.


Slit Lamp Examination Procedure: Six Steps

Work through these in sequence and a slit lamp examination rarely misses much.

Step 1: Set the eyepieces

Match the eyepiece spacing to your own pupillary distance, then set the diopter ring. On the SL-200A, PD adjustment runs from 50 to 82 mm and diopter adjustment covers ±5D, enough range for most examiners to get a clean stereo image.

Step 2: Scan with diffuse light

Start wide and low. Place the beam at 30 to 45 degrees, open the slit fully and keep magnification low to medium. Sweep across the lids, lashes, conjunctiva, sclera and cornea before looking closer at anything.

Step 3: Narrow the beam

A narrower slit turns a flat view into a cross-section. Three beam types do most of the daily work:

  • Parallelepiped: a 2 to 3 mm slit for corneal scars and infiltrates

  • Optical section: a very narrow slit that separates corneal and lens layers

  • Conical beam: a small round spot at 45 to 60 degrees and 16 to 20X, for cells and flare in the anterior chamber

All three are described in the StatPearls review of slit-lamp biomicroscopy.

Step 4: Switch filters

Cobalt blue light plus fluorescein shows corneal defects and the tear layer. The dye goes in with a paper strip or a drop and rinses out with blinking. UCSF Health.[2] The red-free filter makes blood vessels stand out as dark lines. The SL-200A carries four filters: heat absorption, grey, red-free and cobalt blue.

Step 5: Look behind the pupil when needed

Fundus work needs dilation. The drops take 15 to 20 minutes, and the patient stays light-sensitive for a few hours afterward. View the posterior segment through a +90 D or +78 D lens. For applanation tonometry or gonioscopy, apply topical anesthetic first, and tell the patient to bring sunglasses.

Step 6: Record and clean

Write down findings by eye and by structure. Then clean fundus lenses, gonio lenses and prisms with soap and water or an alcohol solution, and let them air dry.

Which Illumination Technique Fits Which Finding

Match the technique to the structure you suspect during the slit lamp examination. StatPearls counts seven basic methods: diffuse, direct focal, indirect, retroillumination, specular reflection, sclerotic scatter and Koeppe's oscillating illumination. The table covers the six you will reach for most.

TechniqueTypical settingBest for
Diffuse30–45°, widest slit, low–medium magnificationLids, conjunctiva, sclera, gross anterior segment
Parallelepiped2–3 mm slitCorneal scars, infiltrates
Optical sectionVery narrow slitCorneal and lens layers, foreign body depth
Conical beam45–60°, 16–20XAqueous cells and flare
Sclerotic scatterBeam at the limbus, 6–10XFaint corneal opacities
Specular reflectionAbout 60° between arms, high magnificationEndothelial cell mosaic

Common Mistakes in a Slit Lamp Test

Rushing causes most errors in a slit lamp examination, and new technicians rush.

  • Jumping to high magnification before locating the lesion at low power

  • Reading ointment or anesthetic haze as corneal disease

  • Leaving bright light on the eye longer than needed

  • Pressing on the eye during tonometry or gonioscopy

Reported complications range from corneal abrasion to vasovagal fainting. Slow hands beat fast ones.

Why Reliable Equipment Matters

The World Health Organization estimates that at least 2.2 billion people live with vision impairment, and at least 1 billion of those cases were preventable or remain unaddressed. Refractive error and cataract lead the causes. World Health Organization.[3] Cataract grading is one of the slit lamp's daily jobs, so a lamp with sharp optics and stable illumination earns its place on the counter.

How to Choose a Slit Lamp for Your Clinic

Choose the instrument for the work, not the brochure.

General clinics and optical shops

The SL-200A slit lamp microscope offers 10X and 16X magnification, a 0–9 mm continuous slit width, a 1–8 mm slit height and a 12V 50W halogen lamp.

Outreach and field screening

The KJ5S1, KJ5S2 and KJ5S3 portable slit lamp microscopes travel better than a bench unit.

Imaging and teaching

The SL-280 slit lamp camera, the SL-400 digital slit lamp and the HSL-200 digital slit lamp camera suit practices that keep image records.

Shanghai Link Instruments, the maker behind LINK, reports more than 15 years in optical equipment, an ISO 9001 and ISO 13485 factory, and CE and FDA certificates on most products. Overseas warehousing has been available since 2017. Browse the full slit lamp range or send an inquiry through the product page.

Best Pick for Most Clinics

For a general ophthalmic clinic, hospital outpatient room or optical shop, start with the SL-200A. Two magnification steps keep the slit lamp examination simple, and four filters cover fluorescein work and vessel checks. Need imaging? Move up to the digital models. Distributors can request OEM and bulk quotes at sales@linkcsh.com.

FAQs

What is a slit lamp examination used for?

It inspects the eyelids, conjunctiva, cornea, iris, lens and anterior chamber. With a handheld lens it also reaches the back of the eye.

How long does a slit lamp test take?

The anterior segment check is brief. Dilation adds 15 to 20 minutes of waiting.

Is a slit lamp exam painful?

No. The patient rests the chin and forehead and looks into bright light. Dilating drops cause light sensitivity for a few hours.

What magnification should I use?

Start low, locate the finding, then raise it. Modern lamps range from 6X to 40X, and conical beam work uses 16 to 20X.

Manual or digital slit lamp: which should I buy?

A manual unit such as the SL-200A handles routine screening. Choose a digital model when you need saved images for records, referrals or teaching.

References

[1] StatPearls (NCBI). Slit-Lamp Biomicroscope. Continuing education article.

[2] UCSF Health. Slit-lamp exam. Reviewed January 20, 2025.

[3] World Health Organization. Blindness and vision impairment. Fact sheet.

Chat with us